ESP8266 Community Forum

Posted: **Thu Jun 04, 2015 3:39 pm**

Is it possible to add an option to read french teleinfo serial datas ?
i'm not developper so i have not successfully get datas and pulled to LUA.
the french teleinfo is simple uart with these parameters :

speed 1200
8 bits but only 7 data bits
no parity
1 stop bit

LUA can't easy manipulate bytes, so i've try to modify the NodeMCU Firmware.

I'm able to display the correct datas with these lines added to /app/modules/uart.c :

Code: Select all

bool uart_on_data_cb(const char *buf, size_t len){
  if(!buf || len==0)
    return false;
  if(uart_receive_rf == LUA_NOREF)
    return false;
  if(!gL)
    return false;
  lua_rawgeti(gL, LUA_REGISTRYINDEX, uart_receive_rf);

  [color=#0040FF]char *char_teleinfo;
  int charpos;
  while (charpos<len)
     {
     c_printf("%c", buf[charpos]&0x7f);
     charpos++;
     }[/color]

  lua_pushlstring(gL, buf, len);

  lua_call(gL, 1, 0);
  return !run_input;
}

but i'm unable to pull this to LUA...
I just want to migrate from a big arduino to a small powerful ESP8266...
the arduino code is like this :

Code: Select all

#include <SoftwareSerial.h>


#define startFrame 0x02
#define endFrame 0x03

SoftwareSerial* cptSerial;

void setup()
{
  Serial.begin(9600);
  
  cptSerial = new SoftwareSerial(8, 9);
  cptSerial->begin(1200);
  Serial.println(F("setup complete"));
}

void loop()
{
  char charIn = 0;

  while (charIn != startFrame)
  {
    charIn = cptSerial->read() & 0x7F;
  }
  
  while (charIn != endFrame)
  {
    if (cptSerial->available())
    {
      charIn = cptSerial->read() & 0x7F;
      Serial.print(charIn);
    }
  }
  
  Serial.println("");
}

I've created an teleinfo emulator based on arduino :
change Serial interface as you need or convert with SoftwareSerial :

Code: Select all

void setup() {
  Serial1.begin(1200,SERIAL_7E1);
}

void loop() {
  Serial1.print((char) 0x02);
  Serial1.print( (char) 0x0A);
  Serial1.print("ADCO 012345678901 F");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("OPTARIF HC.. <");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("ISOUSC 20 8");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("HCHC 036424518 '");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("HCHP 026582379 =");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("PTEC HP..  ");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("IINST1 003 K");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("IINST2 000 I");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("IINST3 001 K");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("IMAX1 019 :");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("IMAX2 020 3");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("IMAX3 018 ;");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("PMAX 08380 9");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("PAPP 00970 1");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("HHPHC E 0");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("MOTDETAT 000000 B");
  Serial1.print( (char) 0x0D);
  Serial1.print( (char) 0x0A);
  Serial1.print("PPOT 00 #");
  Serial1.print( (char) 0x0D);
  Serial1.print((char) 0x03);
}

Regards

Posted: **Thu Jun 04, 2015 5:06 pm**

Before you start trying to develop custom libraries, just make sure that you don't "reinvent the wheel". The bit library give you bit manipulation in Lua. Unfortunately, the SDK and therefore Lua only support 9600 minimum, but there are other example S/W implementations of a serial driver on the forums.

Posted: **Thu Jun 04, 2015 5:22 pm**

TerryE wrote:Before you start trying to develop custom libraries, just make sure that you don't "reinvent the wheel". The bit library give you bit manipulation in Lua. Unfortunately, the SDK and therefore Lua only support 9600 minimum, but there are other example S/W implementations of a serial driver on the forums.

I'm sorry but i've successful get the correct datas with my c_printf, so NodeMCU support 1200bauds.

I just search atm how to put my c_printf to LUA with lua_pushlstring() func

I tried to use the bit library, but i'm unable to do anything... but i'm not a developer

Posted: **Fri Jun 12, 2015 2:58 am**

Hello,
If you have working Arduino code why not using it with esp8266 Arduino ? Should works out of the box and let you Forget LUA for this project ?

ESP8266 Community Forum

uart.on to read teleinfo (EDF) for french users

uart.on to read teleinfo (EDF) for french users

Re: uart.on to read teleinfo (EDF) for french users

Re: uart.on to read teleinfo (EDF) for french users

Re: uart.on to read teleinfo (EDF) for french users