- Thu Sep 18, 2014 9:09 pm
#738
If someone could post the AT firmware compiled to accept a baud rate of 38400 it would be much appreciated 
- Thu Sep 18, 2014 9:22 pm
#740
There you go: http://atelier-klippel.de/at_38400.zip
Greetings,
Chris
Patch wrote:If someone could post the AT firmware compiled to accept a baud rate of 38400 it would be much appreciated
There you go: http://atelier-klippel.de/at_38400.zip
Greetings,
Chris
- Fri Sep 19, 2014 2:43 am
#747
yep, the works very well.
Btw, for those of you who wish to use them in Xtensa Xplorer, simply add at begin of each makefile following lines
(assuming you using my Xplorer installation ESP-IOT-SDK-NOVM.rar from my 1drv http://1drv.ms/1BUD6Nv )
export XTENSA_SYSTEM = C:\usr\xtensa\XtDevTools\install\builds\RC-2010.1-win32\lx106\config
export XTENSA_CORE = lx106
export default_xttools_make_path = C:\usr\xtensa\mingw\bin\make
Then you can simply create new project in Xplorer, choose Unmanaged Xtensa C/C++ Project,
give a name and then simply copy all the sources (the makefile, user, driver, other dirs) into that project dir.
Now refresh the project in project explorer and run project -> project build from menu, that all.
By default, when setting new unmanaged project Xplorer will set build command to ${default_xttools_make_path},
but that might not work properly. Therefore the one extra line in makefile which set the default_xttools_make_path
to make.exe in minngw msys directory (and not the one in Xtensa tools dir).
mamalala wrote:Hi,
attached are updated Makefiles, one for the AT and one for IOT firmware. Basically they are the same, just added the extra libs and stuff to the variables in the IOT version.
yep, the works very well.
Btw, for those of you who wish to use them in Xtensa Xplorer, simply add at begin of each makefile following lines
(assuming you using my Xplorer installation ESP-IOT-SDK-NOVM.rar from my 1drv http://1drv.ms/1BUD6Nv )
export XTENSA_SYSTEM = C:\usr\xtensa\XtDevTools\install\builds\RC-2010.1-win32\lx106\config
export XTENSA_CORE = lx106
export default_xttools_make_path = C:\usr\xtensa\mingw\bin\make
Then you can simply create new project in Xplorer, choose Unmanaged Xtensa C/C++ Project,
give a name and then simply copy all the sources (the makefile, user, driver, other dirs) into that project dir.
Now refresh the project in project explorer and run project -> project build from menu, that all.
By default, when setting new unmanaged project Xplorer will set build command to ${default_xttools_make_path},
but that might not work properly. Therefore the one extra line in makefile which set the default_xttools_make_path
to make.exe in minngw msys directory (and not the one in Xtensa tools dir).
You do not have the required permissions to view the files attached to this post.
I don't want to be human! I want to see gamma rays, I want to hear X-rays, and I want to smell dark matter ...
I want to reach out with something other than these prehensile paws and feel the solar wind of a supernova flowing over me.
I want to reach out with something other than these prehensile paws and feel the solar wind of a supernova flowing over me.
- Fri Sep 19, 2014 9:53 am
#753
If we're talking AT here, please do not add additional signals, but instead perhaps we should add an option for: Echo off, and/or poll incoming data. Being able to poll is much more convenient than using hard signals.
But please please please let's not make the "new" standard require additional signal wires.
But please please please let's not make the "new" standard require additional signal wires.
