ESP8266 Community Forum

- Sun Jun 07, 2015 11:38 am #19758 these are the other files:
wifi.setmode(wifi.STATION)
--Change to match your network
--wifi.sta.config("SSID","PASSWORD")
wifi.sta.config("TP-LINK_XX","yyyyy")
wifi.sta.connect()
tmr.alarm(1, 1000, 1, function()
if wifi.sta.getip()== nil then
print("IP unavaiable, Waiting...")
else
tmr.stop(1)
print("Connected, IP is "..wifi.sta.getip())
dofile("ds18b20-web.lua")
end
end)


-- Set module name as parameter of require
local modname = ...
local M = {}
_G[modname] = M
--------------------------------------------------------------------------------
-- Local used variables
--------------------------------------------------------------------------------
-- DS18B20 dq pin
local pin = nil
-- DS18B20 default pin
local defaultPin = 3
--------------------------------------------------------------------------------
-- Local used modules
--------------------------------------------------------------------------------
-- Table module
local table = table
-- String module
local string = string
-- One wire module
local ow = ow
-- Timer module
local tmr = tmr
-- Limited to local environment
setfenv(1,M)
--------------------------------------------------------------------------------
-- Implementation
--------------------------------------------------------------------------------
C = 0
F = 1
K = 2
function setup(dq)
pin = dq
if(pin == nil) then
pin = defaultPin
end
ow.setup(pin)
end

function addrs()
setup(pin)
tbl = {}
ow.reset_search(pin)
repeat
addr = ow.search(pin)
if(addr ~= nil) then
table.insert(tbl, addr)
end
tmr.wdclr()
until (addr == nil)
ow.reset_search(pin)
return tbl
end

function readNumber(addr, unit)
result = nil
setup(pin)
flag = false
if(addr == nil) then
ow.reset_search(pin)
count = 0
repeat
count = count + 1
addr = ow.search(pin)
tmr.wdclr()
until((addr ~= nil) or (count > 100))
ow.reset_search(pin)
end
if(addr == nil) then
return result
end
crc = ow.crc8(string.sub(addr,1,7))
if (crc == addr:byte(8)) then
if ((addr:byte(1) == 0x10) or (addr:byte(1) == 0x28)) then
-- print("Device is a DS18S20 family device.")
ow.reset(pin)
ow.select(pin, addr)
ow.write(pin, 0x44, 1)
-- tmr.delay(1000000)
present = ow.reset(pin)
ow.select(pin, addr)
ow.write(pin,0xBE,1)
-- print("P="..present)
data = nil
data = string.char(ow.read(pin))
for i = 1, 8 do
data = data .. string.char(ow.read(pin))
end
-- print(data:byte(1,9))
crc = ow.crc8(string.sub(data,1,8))
-- print("CRC="..crc)
if (crc == data:byte(9)) then
t = (data:byte(1) + data:byte(2) * 256)
if (t > 32767) then
t = t - 65536
end
if(unit == nil or unit == C) then
t = t * 625
elseif(unit == F) then
t = t * 1125 + 320000
elseif(unit == K) then
t = t * 625 + 2731500
else
return nil
end
t = t / 10000
-- print("Temperature="..t1.."."..t2.." Centigrade")
-- result = t1.."."..t2
return t
end
tmr.wdclr()
else
-- print("Device family is not recognized.")
end
else
-- print("CRC is not valid!")
end
return result
end

function read(addr, unit)
t = readNumber(addr, unit)
if (t == nil) then
return nil
else
return t
end
end

-- Return module table
return M



Ambro

- Mon Jun 08, 2015 1:57 am #19802 Twaymouyh,
I really do not understand what problem is causing the NO response on the web and on the browser.
Any direction ?
Thanks
Ambro

- Mon Jun 08, 2015 2:07 am #19803 From what I can see all your code looks fine however I have found that if I update my code I need to close the browser tab and re open it before I can get a response. I am currently at work but once I get home I will upload all the files that I am using to produce the rounded temperature reading and hopefully you can use them to achieve the same result.

- Mon Jun 08, 2015 3:34 am #19806 very good,
thanks.
Ambro