Moderator: Mmiscool
- Thu Dec 10, 2015 12:00 am
#36129
Do you mean format runs one time?
You should only have to format it once unless you place more data on it.
How are you connecting as an AP?
192.168.4.1 is the IP...
Do you have the latest Version of espbasic?
I can confirm as well everything is working well.
Try this first....
Visit the interface 192.168.1.4/edit
You will notice there is a blank page no code yet.
Make sure there is also a blank name for the program.
Type this:
print time()
Then save it!
Reset your device by removing the power (USB) Then plug back in and wait 1 minute.
Visit 192.168.1.4 or whatever IP you have it set as if connected to router.
You should now see a time and a date printed.
now visit 192.168.1.4/settings or whatever the IP is for your device with /settings on the end.
At this point you can click the format button and after waiting a minute or 2 your device should be formatted.
Pressing format it replies " 1 " and then frrezes for ever.
Using 1M modules gives the same result.
I do not realized the reason for which it run one time only.
Similar problem has been reported in other post by different user.
Thanks
Ambro
Do you mean format runs one time?
You should only have to format it once unless you place more data on it.
How are you connecting as an AP?
192.168.4.1 is the IP...
Do you have the latest Version of espbasic?
I can confirm as well everything is working well.
Try this first....
Visit the interface 192.168.1.4/edit
You will notice there is a blank page no code yet.
Make sure there is also a blank name for the program.
Type this:
print time()
Then save it!
Reset your device by removing the power (USB) Then plug back in and wait 1 minute.
Visit 192.168.1.4 or whatever IP you have it set as if connected to router.
You should now see a time and a date printed.
now visit 192.168.1.4/settings or whatever the IP is for your device with /settings on the end.
At this point you can click the format button and after waiting a minute or 2 your device should be formatted.
Helpful? Donate To help support Mike http://www.esp8266basic.com click the donate button lets keep this project going and hope we can get the ESP32 in the mix. BEGINNERS GUIDE HERE http://www.esp8266.com/viewtopic.php?f=40&t=6732
Where I buy my ESP8266 boards from... (Banggood)
Where I buy my ESP8266 boards from... (Banggood)
- Sun Dec 20, 2015 12:08 pm
#36834
thanks for the help,
No way to go on for me !
I did re_flash the ESP . After that console continuosly displays the following messages:
ets Jan 8 2013,rst cause:4, boot mode:(3,6)
wdt reset
load 0x4010f000, len 1264, room 16
tail 0
chksum 0x42
csum 0x42
~ld
ets Jan 8 2013,rst cause:4, boot mode:(3,6)
wdt reset
load 0x4010f000, len 1264, room 16
tail 0
chksum 0x42
csum 0x42
~ld
Is there a reason for watch dog reset ? CAUSE 4 BOOT MODE ...
Any direction ?
Thanks
regards
No way to go on for me !
I did re_flash the ESP . After that console continuosly displays the following messages:
ets Jan 8 2013,rst cause:4, boot mode:(3,6)
wdt reset
load 0x4010f000, len 1264, room 16
tail 0
chksum 0x42
csum 0x42
~ld
ets Jan 8 2013,rst cause:4, boot mode:(3,6)
wdt reset
load 0x4010f000, len 1264, room 16
tail 0
chksum 0x42
csum 0x42
~ld
Is there a reason for watch dog reset ? CAUSE 4 BOOT MODE ...
Any direction ?
Thanks
regards
- Sun Dec 20, 2015 12:11 pm
#36835
I have never seen any msgs like that displayed by the esp running basic. Is that the termianl output on boot time?
Serial terminal in the chrome browser see https://serialTerminal.com
http://esp8266basic.com
A BASIC interpreter for your ESP
Working now on Autodrop3d. A 3d printer with automatic part ejection system. https://autodrop3d.com
http://esp8266basic.com
A BASIC interpreter for your ESP
Working now on Autodrop3d. A 3d printer with automatic part ejection system. https://autodrop3d.com
