- Sun Jan 10, 2016 11:36 am
#38426
i noticed that the firmware is a beta version. is there a newer version or a older version that may work better then the beta version ? i was thinking that it may be a bug in the beta version that is not letting me change the baud rate.
- Sun Jan 10, 2016 1:43 pm
#38432
Do a little web searching, but don't get side tracked with other firmwares. You have a working firmware.
Perhaps the entire syntax is necessary.
AT+UART=38400,1,0,0
sometimes quotes are necessary.
https://cdn.sparkfun.com/assets/learn_t ... _v0.30.pdf
Dacflyer wrote:well i tried
AT+UART_DEF? ...... error
AT+UART_CUR? ......error
AT+CIOBAUD? ......error
even tried AT+IPR
nothing works.....
Do a little web searching, but don't get side tracked with other firmwares. You have a working firmware.
Perhaps the entire syntax is necessary.
AT+UART=38400,1,0,0
sometimes quotes are necessary.
https://cdn.sparkfun.com/assets/learn_t ... _v0.30.pdf
- Sun Jan 10, 2016 8:01 pm
#38470
UPDATE >>> ok,, learning is so hard... as you can tell i been at this all weekend,,, do i get any gold star ?
i have got things going now i think,,
i have the current version as shown below in red, and other info i am sure you can decipher.
i initialized the wifi, i got connected to the wifi and went to the IP address 192.168.4.1 and got to the page to fill in the info to get the time as they recommended.
then submitted it,, then clicked activate and submit again.. and then it boots me out of the page, and then i go back into clock settings and turn wifi on. so now i think all is set, but i am waiting on a time update..
i do not know how often it will update tho.. so right now time is incorrect. if time does not update by morning i do not know what else to do.. i'd like to think i did well so far..
advice????
AT+GMR
AT version:0.22.b1.0
SDK version:0.9.6(b1)
OK
AT+UART=38400,8,1,0,0
OK
Žüàà <--- garbage
Communications Error - Check baud rate
üðà <--- more garbage
Baud rate changed to 38400
= node.heap()
ERROR
AT
OK
AT+GMR
AT version:0.22.b1.0
SDK version:0.9.6(b1)
OK
i have got things going now i think,,
i have the current version as shown below in red, and other info i am sure you can decipher.
i initialized the wifi, i got connected to the wifi and went to the IP address 192.168.4.1 and got to the page to fill in the info to get the time as they recommended.
then submitted it,, then clicked activate and submit again.. and then it boots me out of the page, and then i go back into clock settings and turn wifi on. so now i think all is set, but i am waiting on a time update..
i do not know how often it will update tho.. so right now time is incorrect. if time does not update by morning i do not know what else to do.. i'd like to think i did well so far..
advice????
AT+GMR
AT version:0.22.b1.0
SDK version:0.9.6(b1)
OK
AT+UART=38400,8,1,0,0
OK
Žüàà <--- garbage
Communications Error - Check baud rate
üðà <--- more garbage
Baud rate changed to 38400
= node.heap()
ERROR
AT
OK
AT+GMR
AT version:0.22.b1.0
SDK version:0.9.6(b1)
OK
- Sun Jan 10, 2016 8:41 pm
#38471
Gold Stars all around!
I totally think you have done excellently so far. Agreed.
Just got back from the new Star Wars movie. Sooooo campy!!!
We loved it. There was beer.
My guess would have been that time sync should happen pretty quickly.
Do you think there's a chance that you have to actually update the firmware on the arduino (the clock)? The blog post implies that it's a new firmware. Can you tell ON the clock which firmware is running?
Just to confirm: Did you filled in the info on this screen?
http://4.bp.blogspot.com/-v_2dhRvZ_Mc/V ... /setup.JPG
If you HAVE, then that means the clock config and firmware are probably fine.
Any chance it's off by an even number and it's a timezone issue?
What a long strange trip.....
I've learned a few things along the way, that's for sure.
Send a picture of your clock, eh?
Dacflyer wrote:UPDATE >>> ok,, learning is so hard... as you can tell i been at this all weekend,,, do i get any gold star ?
i have got things going now i think,,
i have the current version as shown below in red, and other info i am sure you can decipher.
i initialized the wifi, i got connected to the wifi and went to the IP address 192.168.4.1 and got to the page to fill in the info to get the time as they recommended.
then submitted it,, then clicked activate and submit again.. and then it boots me out of the page, and then i go back into clock settings and turn wifi on. so now i think all is set, but i am waiting on a time update..
i do not know how often it will update tho.. so right now time is incorrect. if time does not update by morning i do not know what else to do.. i'd like to think i did well so far..
advice????
AT+GMR
AT version:0.22.b1.0
SDK version:0.9.6(b1)
OK
AT+UART=38400,8,1,0,0
OK
Žüàà <--- garbage
Communications Error - Check baud rate
üðà <--- more garbage
Baud rate changed to 38400
= node.heap()
ERROR
AT
OK
AT+GMR
AT version:0.22.b1.0
SDK version:0.9.6(b1)
OK
Gold Stars all around!
I totally think you have done excellently so far. Agreed.
Just got back from the new Star Wars movie. Sooooo campy!!!
We loved it. There was beer.
My guess would have been that time sync should happen pretty quickly.
Do you think there's a chance that you have to actually update the firmware on the arduino (the clock)? The blog post implies that it's a new firmware. Can you tell ON the clock which firmware is running?
Just to confirm: Did you filled in the info on this screen?
http://4.bp.blogspot.com/-v_2dhRvZ_Mc/V ... /setup.JPG
If you HAVE, then that means the clock config and firmware are probably fine.
Any chance it's off by an even number and it's a timezone issue?
What a long strange trip.....
I've learned a few things along the way, that's for sure.
Send a picture of your clock, eh?
